Remote Car Key for Ford S-Max 2006 – 2010

This Complete remote car key for Ford is a high-quality replacement or spare. It comes with a 3-button case, uncut blade, 4D63 transponder chip, and 433MHz remote control with battery, ready for cutting and programming.

• Compatibility for: Ford S-Max 2006 – 2010 

Features:

• COMPATIBLE WITH FORD: Designed to fit your vehicle
• COMPLETE & READY FOR PROGRAMMING: Remote and 4D63 transponder chip included, ready after proper setup
• HIGH-QUALITY REPLACEMENT: Ideal for Ford remote key replacement if your old key is broken, worn, or lost
• DURABLE KEY SHELL: Made from high-quality materials for long-lasting use
• UNCUT KEY BLADE: Supplied uncut, can be cut to fit your car
• TRANSPONDER CHIP (ENGINE START): Can be self-programmed to start the engine only if you have 2 original working keys
• REMOTE CONTROL (LOCK / UNLOCK DOORS): Can be self-programmed only if you have at least one working remote key
• INSTRUCTIONS for programming the remote control and transponder chip are below

IMPORTANT NOTES BEFORE PURCHASE:

Why Do You Need a Spare Car Key?

• Peace of Mind – Never get locked out if you lose or damage your only key
• Save Money – A spare costs far less than emergency locksmith services
• Convenience – Perfect for families sharing one car
• Prevent Wear – Switching keys reduces wear on both key and ignition
• Be Prepared – Always have a backup for unexpected situations

Car Key Specification:

• Key Type: Complete Car Key
• Remote Frequency: 433 MHz
• Button: 3
• Blade: HU101 – Uncut (must be cut by a locksmith)
• Chip: 4D63 40 bit transponder
• Transponder Chip (Engine Start): Can be self-programmed if you have master key
• Remote Control (Lock / Unlock Doors): Can be self-programmed if you already have at least one working remote key
• Package Content: Complete Remote Car Key with Battery 

1) Key Blade: Supplied uncut – must be cut by a locksmith.

2) Transponder Chip (for engine start): 

• DIY programming is possible only if you have 2 original working keys.
• If you don't have 2 original working keys, the new key must be programmed by a locksmith.
• Instructions for DIY transponder chip programming (engine start) are provided below

3) Door Remote Control (lock / unlock doors):

• DIY programming is possible only if you already have at least one working remote key.
• If you only have a master key without a remote, the new key must be programmed by a locksmith.
• If your vehicle does not support remote door locking / unlocking, programming is not possible.
• Instructions for DIY remote programming (lock / unlock doors) are provided below

The programming process is divided into two parts:

• (a) programming the remote control for locking and unlocking the doors, and
• (b) programming the transponder chip for engine start.

The two separate instruction sets are listed below.

a) REMOTE CONTROL PROGRAMMING INSTRUCTIONS (LOCK/UNLOCK DOORS)

Preparatory Steps for Remote Control Programming:

• Make sure you have at least one working remote car key.
• When programming, all old remotes will be removed from the car’s memory, so have them ready.
• CLOSE and UNLOCK all doors using the power door locks.
• BUCKLE seat belts.
• Make sure that you don’t press the brake pedal at any time during or before the procedure.

Steps to program the remote control:

• 1. Close all doors, then open driver's door and press the Unlock button on driver’s door while it is open, insert key into ignition.
• 2. Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1)
• 3. Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
• 4. Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4 for all other remotes.
• 5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

Please note:

• If this does not work try the procedure with the door closed
• All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.

b) TRANSPONDER CHIP PROGRAMMING INSTRUCTIONS (FOR ENGINE START):

Preparatory Steps for Remote Control Programming:

• Make sure you have 2 original working keys. If you don't have them, please contact local locksmith.

Steps to program the transponder chip:

• 1. Sit in the driver's seat with doors closed and put the first coded key into the ignition & turn the key to the ACC position. 
• 2. Now turn this key to the OFF position & remove the key.
• 3. Within 5 seconds put the 2nd coded key into the ignition & turn this key to the ON position.
• 4. Turn this key back to the OFF position and remove the key.
• 5. The door locks will then cycle to indicate that the learning mode is active.
• 6. Within 5 seconds put the NEW key into the ignition & turn to the ON position. 
• 7. The door locks will cycle 3 times to indicate the 3rd key has been trained, ensure you wait for the locks to finish cycling before turning the key to the OFF position.
• 8. Repeat this step for any following keys. The 4th key trained will cycle the locks 4 times, and so on. You can train up to a maximum of 8 keys.